Research Field
Energy Storage
Consumables for battery research: coin cells, cylindrical cells, pouch cells and electrode substrates.
Coin Cell Hardware
4 products →
2340 Separator Roll 100mm × 10m — PP/PE/PP 38 µm High-Strength Battery Separator for Na-ion, K-ion, Li-ion, Li-S Cells
2340-spec PP/PE/PP trilayer microporous separator roll — 38 µm, 45% porosity, zero TD shrinkage, puncture strength ≥500 g. 100 mm × 10 m; roughly 30% higher mechanical robustness than 25 µm grades. Cut discs for coin (CR2016/2025/2032), pouch and 18650 cylindrical cell R&D across Na-ion, K-ion, Li-ion and Li-S systems.
1 variantView →
Battery Separator Discs φ18mm — 2320 / 2325 / 2500 | PP/PE/PP Trilayer & PP Monolayer | Na-ion K-ion Li-ion Li-S Cell Separator
φ18 mm pre-punched separator discs covering three mainstream membranes in one listing: 2320 (PP/PE/PP trilayer, 20 µm — thin, energy-dense), 2325 (PP/PE/PP trilayer, 25 µm — balanced workhorse), and 2500 (PP monolayer, 25 µm, 55% porosity — high-rate). Ready to load into CR2032 coin cells and 18 mm test hardware for Na-ion, K-ion, Li-ion and Li-S R&D.
9 variantsView →
CR2025 Coin Cell Case Sets
CR2025 Coin Cell Case Sets (100 Sets), 304 Stainless Steel with Funnel Springs (15.4x1.1mm) and Spacers (15.8x0.5mm), Anti-Static Packaging
1 variantView →
CR2032 Coin Cell Case Kit for Battery Research | LabCore
Complete CR2032 coin cell assembly kit: positive case, negative case, spring and spacer. 100 sets per pack.
1 variantView →
Cylindrical Cell Hardware
1 product →
Electrode Materials
2 products →
Nickel Foam Electrode Substrate | High Porosity for Batteries
Pure nickel foam sheets for electrode substrates. High porosity (95-98%) and conductivity. Ideal for supercapacitors and battery research. Custom sizes available.
2 variantsView →
Solid-State Battery Three-Electrode Test Mold | Compact
Three-electrode split cell with an integrated reference electrode for independent potential monitoring — purpose-built for all-solid-state battery mechanism and interface diagnostics.
1 variantView →
Pouch Cell Materials
3 products →
Aluminum Laminated Film for Pouch Cell Packaging | 88/113μm
3-layer aluminum laminated film (ONy/Al/CPP) for pouch cell fabrication. 88μm and 113μm thickness. Excellent barrier properties. Used in battery research labs worldwide.
2 variantsView →
Battery Tab Kit: 5mm & 8mm Pure Nickel Tabs for Pouch Cells
Matched aluminum and nickel tabs with width-matched sealing tape, supplied in pairs. 5 mm and 8 mm widths.
4 variantsView →
Battery-Grade Aluminum Laminated Film for Pouch Cell Packaging | 76-153μm
Battery-grade aluminum laminated film for pouch cell packaging. Nylon/adhesive/Al/PP multilayer structure with high heat-seal and peel strength. Custom widths, lengths and thicknesses.
1 variantView →
In-Situ Cells
1 product →
testing-equipment
2 products →
Single-Point Pressing Solid-State Battery Test Mold
Single-point axial pressing solid-state battery mold with 5 T stack force, φ10 mm cavity, PEEK-ceramic composite, Standard and With-Sensor variants on one page
2 variantsView →
Three-Point Pressing Solid-State Battery Test Mold
Three-point pressing + PEEK-ceramic composite, dual-seal split-cell design; choose the mechanical or sensor-equipped variant on the same page for the full solid-state workflow from powder to conductivity testing.
2 variantsView →